TurboCAD Forums

The Ultimate Resource for TurboCAD Knowledge

Register
 
When posting a problem be sure to include which version you are using.  Give as much information as possible.  If the problem is with a specific file be sure to attache it to your post.

Cone
Read 285 times
* February 26, 2019, 12:50:47 PM
Flat pattern rolled to form a cone...

Henry H

Logged


* February 26, 2019, 06:22:37 PM
#1
Nice one Henry that looks cool. Just wondering how you rolled it into a cone shape.  Did you use the bend tool or bend to path?

Logged
Daz
TCW V21, 2016-2018 PP, Animation Lab V5, TurboPDF V2-V3 & LightWorks Rendering Engine mostly.


February 27, 2019, 12:01:52 AM
#2
Henry,

Nice job.   8)
I don't know why, but I find myself thinking of earings!   :)

Regards Tim

Logged
You can design without engineering, but you cannot engineer without design.
Using Win 10 with Designer 2017 and TurboCAD Pro. Plat. 2016/2017/2018 + Lightworks (64-bit versions) + AnimationLab.


* February 27, 2019, 12:59:16 AM
#3
Henry,

Nice job.   8)
I don't know why, but I find myself thinking of earings!   :)

Regards Tim
And I think you'd look good in them too!! :-)

Logged
DonCW

2017 Platinum
Light Works Plug in
Windows 10
There's so much to learn and not much time left to learn it.


February 27, 2019, 01:54:23 AM
#4
Henry,

Nice job.   8)
I don't know why, but I find myself thinking of earings!   :)

Regards Tim
And I think you'd look good in them too!! :-)

    I guess, I fell into that one!   ;D

Regards Tim

Logged
You can design without engineering, but you cannot engineer without design.
Using Win 10 with Designer 2017 and TurboCAD Pro. Plat. 2016/2017/2018 + Lightworks (64-bit versions) + AnimationLab.


* February 27, 2019, 07:25:18 AM
#5
NIce one.  I do like the lighting effect,  I think it would look good as an animation. The Spinning cone, with light colour changing  .:)

Logged


* February 27, 2019, 08:32:58 AM
#6
Nice one Henry that looks cool. Just wondering how you rolled it into a cone shape.  Did you use the bend tool or bend to path?

I used Warp by Law. Turned out to be quite a challenge. Although the geometry is fairly straightforward, I ran into several unexpected limitations of the tool and spent a lot of effort finding workarounds.

Henry H

Logged


* February 27, 2019, 09:12:25 AM
#7
Henry,

Nice job.   8)
I don't know why, but I find myself thinking of earings!   :)

Regards Tim
And I think you'd look good in them too!! :-)

    I guess, I fell into that one!   ;D

Regards Tim

SORRY....I couldn't resist.!!

Logged
DonCW

2017 Platinum
Light Works Plug in
Windows 10
There's so much to learn and not much time left to learn it.


* February 27, 2019, 03:29:17 PM
#8
Nice one Henry that looks cool. Just wondering how you rolled it into a cone shape.  Did you use the bend tool or bend to path?

I used Warp by Law. Turned out to be quite a challenge. Although the geometry is fairly straightforward, I ran into several unexpected limitations of the tool and spent a lot of effort finding workarounds.

Henry H

Nice work. Thanks for the info on rolling it up.

Logged
John R.

V17—V21, 2015—2018
Designer, Deluxe, Expert, Basic, Platinum
RedSDK enabled
Windows 10, 64-bit