TurboCAD Forums

The Ultimate Resource for TurboCAD Knowledge

Register
 
Remember to do a search before you ask a question!!!

Explode selection locks my screen
Read 350 times
* May 22, 2018, 05:48:42 AM
Hi again
TCW Pro 2016 Plat' 64bit v23-2 build 61-2
Win 10 Pro latest (April 2018) update.

I attach a tcw & dwg file/s which I cannot 'Explode' the "Section-Main Cway" layer.

BTW I received the file in dwg format which I also attach; it was this dwg that I converted to tcw.

When I select almost any of the detail (lines, grid etc) in either tcw or dwg my setup tries to carry out 'Explode command' but after a number of minutes the programme shows "prog not responding" and I need to use Windows Task Manager to close Turbocad.

Can any one help me to allow me to work on the file.

Logged
quintain
Retired from work not life.
Turbocad 2016 Pro Platinum


* May 22, 2018, 06:16:34 AM
#1
There was many Blocks inside Blocks and when i exploded it first time i get a warning, see Attached.
Normally this is some Hidden line with to small spaces
Attach your drawing exploded as a v 2016 and zip'ed because of filesize

Torfinn

Logged
V18, V19, V20, V21, 2015/ 16/ 17/ 18 Pro. Platinum
Deluxe V20, V21, 2015/ 16/ 17
RedSDK enabled
Windows 10 Home Premium 64 bit, 32 GB
NVIDIA Geforce GTX 780m, 1 GB


* May 22, 2018, 06:30:11 AM
#2
Torfinn.

Thank you again for your help, which allows me to carry out some additional design work.

Should I be concerned and do something about your wording "Normally this is some Hidden line with to small spaces".

Again I thank you for your help.

Best Regards
Richard (quintain)

Logged
quintain
Retired from work not life.
Turbocad 2016 Pro Platinum


* May 22, 2018, 07:08:46 AM
#3
Not conserned, but i would try to find them and set the space to a bigger number, if using world many People use the same as the planned print, aka 100 for a 1:100 print, but you will see if it is ok when changed and maybe give it a different size.
It will make the drawing more easy for TC to work with, and by that quicker.

Torfinn

Logged
V18, V19, V20, V21, 2015/ 16/ 17/ 18 Pro. Platinum
Deluxe V20, V21, 2015/ 16/ 17
RedSDK enabled
Windows 10 Home Premium 64 bit, 32 GB
NVIDIA Geforce GTX 780m, 1 GB


* May 22, 2018, 07:53:07 AM
#4
Thank you Torfinn

I will try to find them and reduce them.

Best Regards
Richard

Logged
quintain
Retired from work not life.
Turbocad 2016 Pro Platinum


* May 22, 2018, 10:20:03 PM
#5
I use 10 times the planned scale for world or device width

Logged
Nikki
TC20 platinum
TC 2015 platinum
TC 2017 with lightworks


* May 23, 2018, 05:22:04 AM
#6
Hello Nicki

How do I do that; i.e where do I go in the programme and can you advise me how to do it on the drawings I sent earlier in this post.

Thank you for your help and interest.

Regards
Richard

Logged
quintain
Retired from work not life.
Turbocad 2016 Pro Platinum