TurboCAD Forums

The Ultimate Resource for TurboCAD Knowledge

Register
 
Interested in some really terrific mobile apps? Visit www.turboapps.com for details.

To save as JPG
Read 354 times
* September 23, 2017, 03:57:14 PM
Hi, Please how I save a drawing with high resolution in JPG type. Many times, I do not why, I can To save to 16.000 - 16.000 pixels but in other times only up to 1.000 - 1.000 pixels that is I need. How can I to crontrol it? Turbocad 20
Thanks
Enrique

Logged


* September 23, 2017, 07:46:34 PM
#1
When saving as "JPG", make sure you select the correct filter. They have "JPG - TurboCAD for Windows JPEG" and "JPG - SDK sample filter JPEG". The "TurboCAD for Windows" filter can go up to 16,000×16,000 pixels, whereas the SDK only allows 1024 as a maximum (and I'm not sure if it actually works).

Logged
John R.

V17—V21, 2015, 2016, 2017
Designer, Deluxe, Expert, Basic, Platinum
RedSDK enabled
Windows 10, 64-bit


* September 23, 2017, 08:14:47 PM
#2
When saving as "JPG", make sure you select the correct filter. They have "JPG - TurboCAD for Windows JPEG" and "JPG - SDK sample filter JPEG". The "TurboCAD for Windows" filter can go up to 16,000×16,000 pixels, whereas the SDK only allows 1024 as a maximum (and I'm not sure if it actually works).
Thank you very much John but I do not can to go up to 16.000x16.000 pixels like JPG yet. But many times I can, I do not why

Logged


* September 23, 2017, 08:24:52 PM
#3
If you uncheck the "Maximum Resolution" option, can you then enter 16000×16000?

Logged
John R.

V17—V21, 2015, 2016, 2017
Designer, Deluxe, Expert, Basic, Platinum
RedSDK enabled
Windows 10, 64-bit


* September 24, 2017, 06:34:28 AM
#4
If you uncheck the "Maximum Resolution" option, can you then enter 16000×16000?
I am sorry because today is Sunday, but with this I also can not reach higher than 1,000x1,000 pixels, thanks John.It is random in my pc.

Logged


* September 24, 2017, 10:01:34 AM
#5
This issue that Enrique reports here is one that I too experience at times-- versions 19 through 21.  It happens when "Saving As..." JPEGs and also PNGs (at a lower resolution value with the PNGs).  I believe I can recall others reporting it on these forums as well.
My experience too seems to be random... arbitrary; although, I would assume there is an underlying technical cause of the issue.

The issue does not occur consistently enough to facilitate investigating as to a cause and remedy. It just goes away after a few sessions and/or re-boots of the system (I think... I don't know exactly when or how it resolves itself).

-Alvin
« Last Edit: September 24, 2017, 11:41:17 AM by Alvin Gregorio »

Logged
Alvin Gregorio
(mostly Residential Architectural 2D; no formal CAD Training; intermittent TurboCAD user since yr. 2000 [ver6.5])
---TurboCAD: V20.2PP(57.0)[as of 3/12/15]; V19DL(54.2); V11.2Pro; Windows-7-Pro/64-bit; Intel-Core-i3 CPU; 2.27ghz; 4GB RAM; Intel HD Graphics (CPU based)


* September 24, 2017, 10:16:06 AM
#6
Seems that the issue might have something to do with inserted Images and/or OLE objects.

Enrique-- do you have either of those in the Drawing's drawing-space (Modelspace or Paperspace) which you are trying to "Save As..." JPG?

Can you share the drawing file with us?

Logged
Alvin Gregorio
(mostly Residential Architectural 2D; no formal CAD Training; intermittent TurboCAD user since yr. 2000 [ver6.5])
---TurboCAD: V20.2PP(57.0)[as of 3/12/15]; V19DL(54.2); V11.2Pro; Windows-7-Pro/64-bit; Intel-Core-i3 CPU; 2.27ghz; 4GB RAM; Intel HD Graphics (CPU based)


* September 24, 2017, 01:19:44 PM
#7
• I opened a Drawing file that I had experienced this issue with in the past.
• It is a simple 2D Drawing, done in version-19.  It has Modelspace, and 4 Paperspaces.
• One of the Paperspaces has two Images inserted and 2 Linked OLE Objects inserted.  This Paperspace has the issue discussed on this thread; Modelspace and the other Paperspaces do not.
• In that Paperspace:  I deleted one of the Images and tried to save the entirety of that Paperspace as a JPG larger than 1000x1000-- was not allowed.  Repeated with the other Image-- same result, not allowed.  • Deleted both of the OLE Objects-- I could successfully Save as a JPG with "Maximum Resolution" of 16000x16000.

Experimented with it some more.  Every time I insert an OLE Object into a drawing space, that drawing space can no longer be Saved As a JPG or PNG larger than 1000 in the height or width fields.

-Alvin

Logged
Alvin Gregorio
(mostly Residential Architectural 2D; no formal CAD Training; intermittent TurboCAD user since yr. 2000 [ver6.5])
---TurboCAD: V20.2PP(57.0)[as of 3/12/15]; V19DL(54.2); V11.2Pro; Windows-7-Pro/64-bit; Intel-Core-i3 CPU; 2.27ghz; 4GB RAM; Intel HD Graphics (CPU based)


* September 24, 2017, 02:11:57 PM
#8
re: …Every time I insert an OLE Object into a drawing space, that drawing space can no longer be Saved As a JPG or PNG larger than 1000 in the height or width fields.

Confirm in Version 20. So far Version 2017 seems to work okay.

I inserted an Excel file into a drawing that worked okay, sorta, just before and now it won't go over 1000.

"sorta" = I could get 16000 in the "Setup" dialog, but it wouldn't save to that size (error message). It would save to JPG at 8000.

The error message I received was:
Graphic board runs out of system memory, and the RED requested memory allocation could not be performed.
The engine is still safe, but can't draw with the resource that could not be created.

Failed to save document.

Logged
John R.

V17—V21, 2015, 2016, 2017
Designer, Deluxe, Expert, Basic, Platinum
RedSDK enabled
Windows 10, 64-bit


* September 25, 2017, 07:37:33 AM
#9
re: …Every time I insert an OLE Object into a drawing space, that drawing space can no longer be Saved As a JPG or PNG larger than 1000 in the height or width fields.

Confirm in Version 20. So far Version 2017 seems to work okay.

I inserted an Excel file into a drawing that worked okay, sorta, just before and now it won't go over 1000.

"sorta" = I could get 16000 in the "Setup" dialog, but it wouldn't save to that size (error message). It would save to JPG at 8000.

The error message I received was:
Graphic board runs out of system memory, and the RED requested memory allocation could not be performed.
The engine is still safe, but can't draw with the resource that could not be created.

Failed to save document.

Alvin, Jonh thanks for your interest: In effect in my drawing I have inserted images. Attached 2 drawings in first are the images taken from a map of my city and Turbocad identifies them as OLC images. These images do not allow to move or to turn but if they are selected in Inspector Bar it appears a command that says "Convert picture to raster image" and in this form can rotate all the dibijo to where I need it, is the drawing last that I attached.
I can not go through 1,000x1,000 pixels in any of the two and erase the images either. But at first I could reach 6,000x6,000 in the drawing first
As you can see the whole drawing I did on the images that are an essential part of drawing especially in last.
Since yesterday I tried to send the drawings but I could not

Logged


* September 25, 2017, 07:59:39 AM
#10
Attach two images, I can´t to send the TCW Drawings, I do not why

Logged


* September 25, 2017, 06:12:05 PM
#11
It seems to me Enrique that you Copied-and-Pasted the images of the City into your drawing.  I wouldn't do that; I never do it that way.  I believe that might be the core of the issue.

Delete all the Images that you Copied/Pasted into your Drawing.
Re-Insert them using the proper method:  Use the Insert/Picture/From File... method-- using the Images that you have previously saved onto your hard-drive.  I hope that your Workspace configuration has that Command within the Insert menu.  If not, you are going to have to find it another way.

Ensure that you cleared (Deleted... removed) all the OLE Objects-- all the Images that you Copied/Pasted into the Drawing.

Please report back after you do that.  Thanks.

____________
Note:  Your TurboCAD Desktop and Insert Menu contents will probably look different than mine shown below.  Mine has been customized by me.

-Alvin
« Last Edit: September 25, 2017, 07:01:58 PM by Alvin Gregorio »

Logged
Alvin Gregorio
(mostly Residential Architectural 2D; no formal CAD Training; intermittent TurboCAD user since yr. 2000 [ver6.5])
---TurboCAD: V20.2PP(57.0)[as of 3/12/15]; V19DL(54.2); V11.2Pro; Windows-7-Pro/64-bit; Intel-Core-i3 CPU; 2.27ghz; 4GB RAM; Intel HD Graphics (CPU based)


* September 25, 2017, 06:16:59 PM
#12
Alternatively:  You could go ahead and do that "Convert picture to raster image" command to each and all the OLE images that you Copied/Pasted into the Drawing.

Logged
Alvin Gregorio
(mostly Residential Architectural 2D; no formal CAD Training; intermittent TurboCAD user since yr. 2000 [ver6.5])
---TurboCAD: V20.2PP(57.0)[as of 3/12/15]; V19DL(54.2); V11.2Pro; Windows-7-Pro/64-bit; Intel-Core-i3 CPU; 2.27ghz; 4GB RAM; Intel HD Graphics (CPU based)


* September 25, 2017, 07:45:50 PM
#13
Alternatively:  You could go ahead and do that "Convert picture to raster image" command to each and all the OLE images that you Copied/Pasted into the Drawing.
Alvin, everything that you explained I did the first time, however I decided to repeat it in a new drawing: I inserted the same images from the previous drawing and oh surprise! I can rotate the images and when trying to save as JPG I get up to 16,000x16,000 pixels if I wish.
Now I will pass the entities of the previous drawing to the new drawing and I hope I have no problems. For now I have my problem solved, thank you very much.
(but the puzzle continues ...)
A greeting for Alvin and Jonh R!



Logged