TurboCAD Forums

The Ultimate Resource for TurboCAD Knowledge

Register
 
When replying to a specific statement be sure to quote the previous post.

Is CADCourse interface available in TC Pro Platinum 2015, 2016 and 2017?
Read 246 times
* June 23, 2017, 09:46:56 AM
Hi Everyone
I would like to know if the "CadCourse" interface for TC Pro Platinum is available in the Pro Platinum version 2015, 2016 and 2017?. It comprises of a series of tabs, which contain the tools and toolbar(s). I have got used to using it since TC pro Platinum 15.2 It exists in Pro Platinum 21.2. I downloaded a trial version of Pro Platinum 2017 but it was not offered as an option.

Anybody know for sure?

Thanks
Michael

Logged
Michael Campbell
TurboCad Pro Platinum v21.2, Windows 10 Pro 64, AMD Ryzen 1600X, 16Gb  ram, AMD Firepro W4100 graphics


* June 23, 2017, 10:10:23 AM
#1
I dont have CADcourse in 2017 but i have CADcourse v21 in my 2016 version

Torfinn

Logged
V18, V19, V20, V21, 2015 Pro. Platinum
Deluxe V20, V21, 2015
RedSDK enabled
Windows 10 Home Premium 64 bit, 32 GB
NVIDIA Geforce GTX 780m, 1 GB


* June 23, 2017, 10:18:37 AM
#2
Its not available as an 'supplied' option, and although I don't use it , after copy/paste it apparently works in later versions.

Here are two threads on a similar subject,  just ensure the files are pasted in the correct place.

http://forums.turbocad.com/index.php/topic,18912.msg111992.html#msg111992
http://forums.turbocad.com/index.php/topic,20753.msg124498.html#msg124498
« Last Edit: June 23, 2017, 10:26:27 AM by Andy H »

Logged


* June 23, 2017, 05:02:50 PM
#3
Thanks Andy H for the tip. I'll try this and see if it works in TC Pro Platinum 2017 ....

Regards
Michael

Logged
Michael Campbell
TurboCad Pro Platinum v21.2, Windows 10 Pro 64, AMD Ryzen 1600X, 16Gb  ram, AMD Firepro W4100 graphics


June 23, 2017, 05:42:23 PM
#4
I have been copying my V15 configuration into successive versions of TurboCAD for years. 

If you accepted the default installation locations, you will have to have to be in Administrator Mode to add files to the folder.  You will also have to add the new commands to the desired menus.


Jeff


Logged
TC Pro Platinum 2017, 2016 & 2015 (all with LightWorks) & V21
System: i7-5820K @ 3.30GHz, ASRock X99 Extreme4, 16GB DDR4-2133 RAM, Gigabyte GTX 970, Samsung NVMe SSD 950 (256GB), Windows 7 Pro (64-bit) SP1


* June 23, 2017, 09:44:16 PM
#5
I have been copying my V15 configuration into successive versions of TurboCAD for years. 

If you accepted the default installation locations, you will have to have to be in Administrator Mode to add files to the folder.  You will also have to add the new commands to the desired menus.

Jeff

I've never had to do that. I paste the copies of the configuration files into the "Config" folder located in my "Documents" folder (This PC > Documents > TurboCAD 2017 Professional x64 > Config).

Logged
John R.

V17—V21, 2015, 2016, 2017
Designer, Deluxe, Expert, Basic, Platinum
RedSDK enabled
Windows 10, 64-bit


June 23, 2017, 10:00:21 PM
#6
I've never had to do that. I paste the copies of the configuration files into the "Config" folder located in my "Documents" folder (This PC > Documents > TurboCAD 2017 Professional x64 > Config).

On my system, the C:\ root has "Documents and Settings", but entering that folder takes me to "C:\Users\".  From there, I move down the folder tree as shown below.

C:\Users\Jeff\Documents\TurboCAD 2017 Professional x64\Config

I still have to be in Administrator Mode to edit or add anything.


Jeff

Logged
TC Pro Platinum 2017, 2016 & 2015 (all with LightWorks) & V21
System: i7-5820K @ 3.30GHz, ASRock X99 Extreme4, 16GB DDR4-2133 RAM, Gigabyte GTX 970, Samsung NVMe SSD 950 (256GB), Windows 7 Pro (64-bit) SP1


* June 26, 2017, 05:23:22 AM
#7
Hi Everyone

Thank you all for your comments and suggestions. I did what Andy H suggested and copied my v21.2 files to the TC Pro Plat 2017 Config directory and was able to select it when TC pro plat started. It took a bit of a while to get it displayed, but it seems to work correctly now. I have got so used to using this interface because it groups the functions into a set of logically-ordered tabs which makes it easy to find all the related functions you need and takes up less screen space than having multiple tool-bars.

Kind Regards
Mike
« Last Edit: June 28, 2017, 03:05:03 PM by MikeyC38 »

Logged
Michael Campbell
TurboCad Pro Platinum v21.2, Windows 10 Pro 64, AMD Ryzen 1600X, 16Gb  ram, AMD Firepro W4100 graphics